miniroot.img boot-looping on rpi-4b

Discussion:

Rob Whitlock

2021-05-08 22:55:57 UTC

Hello,

I am trying to install OpenBSD 6.9 on a Raspberry Pi 4B. I copied
miniroot69.img to the SD card with this command:

dd if=miniroot69.img of=/dev/rdisk2 bs=1m

I put it in the Pi and upon boot it fails with this error message
printed out through serial:

U-Boot 2021.01 (Apr 16 2021 - 15:39:01 +1000)

DRAM: 1.9 GiB
RPI 4 Model B (0xb03114)
MMC: ***@7e300000: 1, ***@7e340000: 0
Loading Environment from FAT... ** No partition table - mmc 0 **
In: serial
Out: serial
Err: serial
Net: eth0: ***@7d580000
PCIe BRCM: link up, 5.0 Gbps x1 (SSC)
starting USB...
Bus xhci_pci: probe failed, error -110
No working controllers found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
** Bad device specification :1 bootfstype **
"Synchronous Abort" handler, esr 0x96000004
elr: 000000000009197c lr : 00000000000930c8 (reloc)
elr: 000000003b36d97c lr : 000000003b36f0c8
x0 : 6d63625f646e7320 x1 : 000000005f656c62
x2 : 000000003b3d30a0 x3 : 0000000000000001
x4 : 000000003afe9fe0 x5 : 0000000000000000
x6 : 000000003b3d30a0 x7 : 000000003b3d30b0
x8 : 000000003afea070 x9 : 0000000000000008
x10: 000000003b3d07f2 x11: 000000003af64780
x12: 0000000000000000 x13: 0000000000000004
x14: 000000003af4be58 x15: 00000000ffffffff
x16: 0000000000004110 x17: 2285e5950900a046
x18: 000000003af57da0 x19: 000000003afe9940
x20: 0000000000000811 x21: 0000000000000811
x22: 0000000000000000 x23: 0000000000000000
x24: 0000000000000000 x25: 0000000000000000
x26: 0000000000000028 x27: 0000000000000003
x28: 00000000ffffffff x29: 000000003af4bac0

Code: 2a1b03e1 97ffffe5 2a0003f8 1400000d (f8777800)
Resetting CPU ...

resetting ...

Any help would be appreciated.

Rob

Justin Yang

2021-05-09 09:20:16 UTC

Permalink

Do you have any USB disks connected to your pi? If so, try to remove that
and boot again to see if it works.

Post by Rob Whitlock
Hello,
I am trying to install OpenBSD 6.9 on a Raspberry Pi 4B. I copied
dd if=miniroot69.img of=/dev/rdisk2 bs=1m
I put it in the Pi and upon boot it fails with this error message
U-Boot 2021.01 (Apr 16 2021 - 15:39:01 +1000)
DRAM: 1.9 GiB
RPI 4 Model B (0xb03114)
Loading Environment from FAT... ** No partition table - mmc 0 **
In: serial
Out: serial
Err: serial
PCIe BRCM: link up, 5.0 Gbps x1 (SSC)
starting USB...
Bus xhci_pci: probe failed, error -110
No working controllers found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
** Bad device specification :1 bootfstype **
"Synchronous Abort" handler, esr 0x96000004
elr: 000000000009197c lr : 00000000000930c8 (reloc)
elr: 000000003b36d97c lr : 000000003b36f0c8
x0 : 6d63625f646e7320 x1 : 000000005f656c62
x2 : 000000003b3d30a0 x3 : 0000000000000001
x4 : 000000003afe9fe0 x5 : 0000000000000000
x6 : 000000003b3d30a0 x7 : 000000003b3d30b0
x8 : 000000003afea070 x9 : 0000000000000008
x10: 000000003b3d07f2 x11: 000000003af64780
x12: 0000000000000000 x13: 0000000000000004
x14: 000000003af4be58 x15: 00000000ffffffff
x16: 0000000000004110 x17: 2285e5950900a046
x18: 000000003af57da0 x19: 000000003afe9940
x20: 0000000000000811 x21: 0000000000000811
x22: 0000000000000000 x23: 0000000000000000
x24: 0000000000000000 x25: 0000000000000000
x26: 0000000000000028 x27: 0000000000000003
x28: 00000000ffffffff x29: 000000003af4bac0
Code: 2a1b03e1 97ffffe5 2a0003f8 1400000d (f8777800)
Resetting CPU ...
resetting ...
Any help would be appreciated.
Rob

--
Justin Yang

Rob Whitlock

2021-05-09 12:05:33 UTC

Permalink

Nothing is connected to the Pi except the USB-C for power, the SD
card, and the 3 serial wires.

Post by Justin Yang
Do you have any USB disks connected to your pi? If so, try to remove that
and boot again to see if it works.

--
Justin Yang